Product ID:BLUE SEMI-GLOSS ENAMEL, 300
MSDS Date:02/09/1989
FSC:8010
NIIN:00N018533
MSDS Number: BLDLP

FARWEST PAINT MANUFACTURING CO

133RD ST
TUKWILA, WA 98168
US

Emergency Phone: 206-941-1619

Info Phone: 206-244-8844

Cage: 2F266

FARWEST PAINT MANUFACTURING CO

TUKWILA, WA 98168 US

Telephone: 206-244-8844

Cage: 6F266

2.0 MM/HG @ 68F

Fraction By Weight: 43-48%

OSHA PEL 500 PPM (MFR)

ACGIH TLV: 100 PPM (MFR)

1.0 @ 68F

Fraction By Weight: <2.00%

OSHA PEL 500 PPM (MFR)

ACGIH TLV: 100 PPM (MFR)

OTHER ADDITIVES

Fraction By Weight: <0.25%

FLOOR ABSORB OR OTHER ABSORB MATL. PVNT RUN-OFF

RTECS: 9999999ZZ

OCCURS, NOTIFY PROPER AUTH AS REQD THAT A SPILL HAS

RTECS: 9999999ZZ

SFTY EQUIPMENT SUPPLIER. ENGINEERING OR

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYE:CAN CAUSE SEV IRRIT, REDNESS,
TEARING OR BLURRED VISION. SKIN:PRLNGD/RPTD CONT CAN CAUSE MOD
IRRIT, DEFATTING & DERM. INHAL:EXCESSIVE INHAL OF VAPS CAN CAUSE
NASAL & RESP IRRIT, DIZZ, WEAK, FATIGU E, NAUS, HDCH, POSS UNCON &
EVEN ASPHY.INGEST:CAN CAUSE GI IRRIT, NAUS, VOM & DIARR. ASPIR OF
(SEE EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ:MATL INTO THE LUNGS CAN CAUSE CHEM
PNEUM WHICH CAN BE FATAL.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:SKIN:THORO WASH EXPOSED AREA W/SOAP & WATER. REMOVE CONTAMD
CLTHG. LAUNDER CONTAMD CLTHG BEFORE REUSE. EYE:FLUSH W/LGE AMTS OF
WATER FOR AT LEAST 15 MINS, LIFTING UPPER & LOWER LIDS OCCASNLY.
GET MD. INGEST:DO NOT INDUCE VOM. KEEP PERS WARM, QUIET & GET MD.
ASPIR OF MATL INTO THE LUNGS DUE TO VOM CAN CAUSE CHEM PNEUM WHICH
CAN BE FATAL. INHAL:IF AFFECTED, REMOVE INDIV TO FRESH AIR. (SEE
SUPP DATA)

Flash Point Method:TCC
Flash Point:100F,38C
Lower Limits:1%
Extinguishing Media:FOAM, CARBON DIOXIDE OR DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NEVER USE NEAR OR AROUND WELDERS OR
CUTTING TORCHES. DRUM (EVEN EMPTY) BECAUSE PRODUCT (EVEN JUST
RESIDUE) CAN IGNITE EXPLOSIVELY.

Spill Release Procedures:SMALL:ABSORB LIQ ON PAPER, VERMICULITE, FLOOR
ABSORB OR OTHER ABSORB MATL & TRANSFER TO HOOD. LGE:ELIM ALL IGNIT
SOURCES (FLARES, FLAMES, INCL PILOT LIGHTS, ELEC SPARKS). PERS NOT
WEARING PROT EQUIP S HOULD BE EXCLUDED FROM AREA OF (SEE SUPP DATA)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:CONTRS OF THIS MATL MAY BE HAZ WHEN
EMPTIED, SINCE EMPTIED CONTRS RETAIN PROD RESIDUES (VAP, LIQ &/OR
SOLID).
Other Precautions:ALL HAZARD PRECAUTIONS GIVEN IN THE DATA SHEET MUST
BE OBSERVED.

Respiratory Protection:IF TLV OF THE PROD OR ANY COMPONENT IS EXCEEDED,
A NIOSH/MSHA APPRVD AIR SUPPLIED RESP IS ADVISED IN ABSENCE OF
PROPER ENVIRON CONTROL. OSHA REGS ALSO PERMIT OTHER NIOSH/MSHA
APPRVD RESPS UNDER SPECIF IED CNDTNS. SEE YOUR (SEE INGRED 6)
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL &/OR LOCAL EXHAUST)
VENTILATION TO MAINTAIN EXPOSURE BELOW TLV(S).
Protective Gloves:RESISTANT GLOVES (NITRILE).
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:TO PREVENT REPEATED OR PROLONGED SKIN
CONTACT, WEAR IMPERVIOUS CLOTHING & BOOTS.
Work Hygienic Practices:KEEP WORK AREA CLEAN & FREE FROM LEAKS &
SPILLS. ALWAYS WASH HANDS THORO W/SOAP & WATER BEFORE HNDLG FOOD &
DRINK.
Supplemental Safety and Health
FIRST AID PROC:IF BRTHG IS DFCLT, ADMINISTER O2. IF BRTHG HAS STOPPED,
GIVE ARTF RESP. KEEP PERS QUIET & GET MD. SPILL PROC:SPILL UNTIL
CLEAN-UP HAS BEEN COMPLETED. STOP SPILL AT SOURCE, DIKE AREA OF
SPILL TO PVNT SPREADING, PUMP LIQ TO SALVAGE TANK. REMAINING LIQ
MAY BE TAKEN UP ON SAND, CLAY, EARTH, (SEE INGRED 4)

HCC:F4
Boiling Pt:B.P. Text:300F,149C
Vapor Density:HVR/AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:BLUE LIQUID W/MILD, SWEET AROMATIC ODOR.
Percent Volatiles by Volume:<46

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:KEEP AWAY FROM OPEN FLAMES, SPARKS & HEAT.
DO NOT WELD NEAR OR AROUND PRODUCT.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

Waste Disposal Methods:DESTROY BY LIQUID INCINERATION. CONTAMINATED
ABSORBENT MAY BE DEPOSITED IN A LANDFILL IN ACCORDANCE W/LOCAL,
STATE & FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.